Each base board of the SIRIUS can hold 8 standard amplifiers (modules). These can be isolated or non-isolated and are:
In addition to standard 8 channel configuration modules we also offer completly customizable user-configurable 8 channel modules.
Base station for SIRIUS modules features fully flagged PC (Intel Core i7 2.0 Ghz, 4GB RAM, 8GB flash hard drive, 64GB removable SSD card) with wide range of connectivity interfaces (5xUSB port, VGA, GLAN, WLAN, 2xSync). Using S-BOX option, SIRIUS can be used as a standalone measurement unit.
| SIRIUSi ACC 8 |
SIRIUS ACC 8 |
SIRIUSi MULTI 8 |
SIRIUS MULTI 8 |
SIRIUSi STG 8 |
SIRIUS STG 8 |
SIRIUSi ACC 8 CNT 2 |
SIRIUS ACC 8 CNT 2 |
SIRIUSi HV 8 |
|||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Channels | 8 | 8 | 8 | 8 | 8 | 8 | 8+2 | 8+2 | 8 | ||
| Data rates / channels [Hz] | 200 k | 200 k | 200 k | 200 k | 200 k | 200 k | 200 k | 200 k | 200 k | ||
| Vertical resolution | 2 * 24 bit | 2 * 24 bit | 2 * 24 bit | 2 * 24 bit | 2 * 24 bit | 2 * 24 bit | 2 * 24 bit | 2 * 24 bit | 2 * 24 bit | ||
| Isolation voltage [V] | 1 kV | - | 1 kV | - | 1 kV | - | 1 kV | - | 1.5 kV 4 kV peak |
||
| Input types | |||||||||||
 |
Voltage | 8 ch. | 8 ch. | 8 ch. | 8 ch. | 8 ch. | 8 ch. | 8 ch. | 8 ch. | 8 ch. | |
| Max. range | ± 10 V ± 500 mV autorange |
± 10 V ± 500 mV autorange |
± 10 V ± 500 mV autorange |
± 10 V ± 500 mV autorange |
± 50 V ± 10 V ± 1V 2mV/v…100mV/V autorange |
± 50 V ± 10 V ± 1V 2mV/v…100mV/V autorange |
± 10 V ± 500 mV autorange |
± 10 V ± 500 mV autorange |
± 1000 V ± 50 V autorange |
||
| Input coupling | DC AC 1 Hz |
DC AC 1 Hz |
DC | DC | DC | DC | DC AC 1 Hz |
DC AC 1 Hz |
DC | ||
 |
IEPE/ICP Sensors | 8 ch. | 8 ch. | MSI option | MSI option | MSI option | MSI option | 8 ch. | 8 ch. | ||
| Sensor supply per channel | 4 or 8 mA max 25 V |
4 or 8 mA max 25 V |
programmable up to 15 V 100 mW |
programmable up to 15 V 100 mW |
programmable up to 20 V or 45 mA 100 mW |
programmable up to 20 V or 45 mA 100 mW |
4 or 8 mA max 25 V |
4 or 8 mA max 25 V |
|||
 |
Bridge connection type | 8 ch 2, 3, 4, 5, 6 wire connection |
8 ch 2, 3, 4, 5, 6 wire connection |
8 ch 2, 3, 4, 5, 6 wire connection |
8 ch 2, 3, 4, 5, 6 wire connection |
||||||
| Bridge completion programmable | full bridge, half bridge 1 kOhm quarter bridge 120 and 350 Ohm | full bridge, half bridge 1 kOhm quarter bridge 120 and 350 Ohm | full bridge, half bridge 1 kOhm quarter bridge 120 and 350 Ohm | full bridge, half bridge 1 kOhm quarter bridge 120 and 350 Ohm | |||||||
| Short and shunt programmable | |||||||||||
 |
Counter | 8 ch | 8 ch | 2 ch | 2 ch | ||||||
| TEDS support | |||||||||||
 |
Resistance | 8 ch | 8 ch | ||||||||
 |
Potentiometer | 8 ch | 8 ch | 8 ch | 8 ch | ||||||
 |
Pt100, Pt1000 | MSI option | MSI option | 8 ch | 8 ch | ||||||
 |
Thermocouple | MSI option | MSI option | 8 ch | 8 ch | ||||||
|
Charge | MSI option | MSI option | MSI option | MSI option | ||||||
| Output signal | |||||||||||
|
Voltage (±10 V) | 8 ch 200 kS/s |
8 ch 200 kS/s |
||||||||
| CAN BUS | 1 ch | 1 ch | 1 ch | 1 ch | 1 ch | 1 ch | 1 ch | 1 ch | 1 ch | ||
| Output signal | |||||||||||
| BNC | 8 | 8 | 8 | 8 | |||||||
| DSUB 15 | 8 | 8 | |||||||||
| DSUB 9 | 8 | 8 | |||||||||
| LEMO 7pin | 2 | 2 | |||||||||
| Banana | 8 | ||||||||||
SIRIUS documents |
|||||||||||
| Inputs: | Voltage, IEPE |
| ADC type: | 24 bit sigma delta dual core with anti-aliasing filter (see section ADC) |
| Sampling rate: | Simultaneous 200kS/sec sampling rate |
| Dynamic range: | 165 dB@ auto range |
| Input coupling: | DC, AC 1 Hz |
| Input impedance: | 1 MOhm in parallel with 0.4 nF |
| Sensor supply: | 4 or 8 mA, max. 25 V |
| IEPE voltage range: | 4 to 19 V |
| IEPE voltage < 4 V: | Shortcut detection |
| IEPE voltage > 19 V: | No sensor detection |
| SNR: | 135dB@ auto range, 50 kHz rate |
| Connector type: | BNC |
| Input coupling: | DC, AC (1 Hz filter) |
| TEDS support: | Yes, for IEPE sensors |
| Supported TEDS chips: | DS2406, DS2430A, DS2432, DS2433 |
| Power consumption: | Typically 0.8 to 1.0 W (depending on sensor) |
| Protection: | 60 V in+ to in- |
| Isolation (isolated version): | 1 kV |
| Inputs: | Voltage, IEPE |
| ADC type: | 24 bit sigma delta dual core with anti-aliasing filter (see section ADC) |
| Sampling rate: | Simultaneous 200kS/sec sampling rate |
| Dynamic range: | 165 dB@ auto range |
| Input coupling: | DC, AC 1 Hz |
| Input impedance: | 1 MOhm in parallel with 0.4 nF |
| Sensor supply: | 4 or 8 mA, max. 25 V |
| IEPE voltage range: | 4 to 19 V |
| IEPE voltage < 4 V: | Shortcut detection |
| IEPE voltage > 19 V: | No sensor detection |
| SNR: | 135dB@ auto range, 50 kHz rate |
| Connector type: | BNC |
| Input coupling: | DC, AC (1 Hz filter) |
| TEDS support: | Yes, for IEPE sensors |
| Supported TEDS chips: | DS2406, DS2430A, DS2432, DS2433 |
| Counters (we can use either counter or analog): | 1 counter and 3 analog input fully synchronized with analog |
| Modes: | Counting, Waveform timing, Encoder, Tacho, Geartooth sensor |
| Power consumption: | Typically 0.8 to 1.0 W (depending on sensor) |
| Protection: | 60 V in+ to in- |
| Isolation (isolated version): | 1 kV |
| Inputs: | Voltage, strain, counter, digital |
| ADC type: | 24 bit sigma delta dual core with anti-aliasing filter (see section ADC) |
| Sampling rate: | Simultaneous 200 kS/sec sampling rate |
| Input ranges: | ±10V(500mV), ±1V, ±100mV(5mV), autorange |
| Dynamic range (SNR): | 135 dB@ autorange 125 dB@ autorange, 50 kHz |
| Counters (we can use either counter or analog): | 1 counter/3 digital input, fully synchronized with analog |
| Modes: | Counting, waveform timing, encoder, tacho, geartooth sensor |
| Bridge connection type: | 3, 4, 5, 6 wire connection |
| Overvoltage protection: | ±30 V input protection |
| Bridge completion: | Full bridge, half bridge (1 kOhm resistors), quarter bridge (120 Ohm, 350 Ohm) |
| Sensor supply: | Programmable 0-25 V, 5 V, 15 V fixed or 45 mA 100 mW |
| Short: | Software selectable |
| Shunt resistor: | 59 kOhm, 175 kOhm, software selectable |
| Analog outputs: | 1 channel 24 bit sigma delta 200 kHz |
| Connector type: | DSUB15 |
| TEDS support: | Standard + MSI adapters |
| Isolation (isolated version): | 1 kV optical |
| Inputs: | Voltage, full bridge strain, half bridge strain, quarter bridge strain, potentiometer, RTD |
| ADC type: | 24 bit sigma delta dual core with anti-aliasing filter (see section ADC) |
| Sampling rate: | simultaneous 200 kS/sec sampling rate |
| Input ranges: | ±50 V (2.5 V), ±10 V (500 mV), ±1V (50 mV), autorange |
| Connection type: | 3, 4, 5, 6 wire connection |
| Short: | Software selectable |
| Shunt resistor: | 59 kOhm, 175 kOhm, software selectable |
| Bridge completion: | Half bridge, quarter bridge 120 Ohm, 350 Ohm |
| Sensor supply: | Programmable 0 to 20 V or 45 mA 100 mW |
| Dynamic range: | 107 dB@ ±10V range, 50 kHz rate 100 dB@ ±100 mV range, 50 kHz rate 125 dB@ auto range, 50 kHz rate |
| Connector type: | DSUB9 |
| TEDS support: | Standard + MSI adapters |
| Protection: | IN+ to IN- line voltage |
| Isolation (isolated version): | 1 kV |
| Inputs: | Voltage |
| ADC type: | 24 bit sigma delta dual core with anti-aliasing filter (see section ADC) |
| Input ranges: | ±1000V, ±50V, autorange |
| Dynamic range: | 107dB@ ±1000V range, 50 kHz rate 100dB@ ±50V range, 50 kHz rate 125dB@ auto range, 50 kHz rate |
| Connector type: | Banana plugs |
| Isolation (isolated version): | 1.5 kV |
Technical specifications of custom module depends of the configuration selected.
| Embedded PC: | CPU: INTEL® Core i7 2.0 GHz Chipset: INTEL QM57 |
| Memory: | 4 GB RAM |
| Storage: | 8 GB internal flash HDD 64 GB removable SSD |
| Interfaces: | 5xUSB VGA GLAN WLAN 2xSync |
SIRIUS allows you to build a variety of different configurations. Build 8, 16, 24 or 32 channel configurations from pre-build standard modules or your completely custom modules.
